Scorpion S-5030-220kv (F3A Special) Brushless Outrunner Motor

К сожалению, у нас нет точной информации, когда ожидаются поставки конкретных товаров. Лучше не добавлять в посылку отсутствующие товары, либо быть готовым ожидать неходовые товары несколько месяцев. Были случаи, что отсутствующие товары исключались из продажи.
Имеет смысл разделить посылки. Одна полностью укомплектованная, другая с отсутствующими товарами.

Чтобы после прихода на склад отсутствующий товар автоматически зарезервировался за Вами, необходимо оформить и оплатить его в заказе.

• Описание товара на английском от 4 июля 2011 г.

  Scorpion S-5030-220KV motor is specially designed for F3A and run on 10 Li-Po cells with props in the 19 to 20 inch range. Everything possible has been done on this motor to get the most possible power at the lightest possible weight. The Front housing, Bearing Tube and flux ring have been made as light as possible, and a Titanium Main Shaft is used to save even more weight, while maintain strength.

  Scorpion Competition Series Brushless Motors are built from the best materials available, and are designed to provide both quality and performance at an affordable price. Scorpion starts with high quality aluminum alloy parts that are produced on the latest CNC milling machines. These parts are then gold Electro-Plated to provide a beautiful, long-lasting finish. The stators are made with 0.2mm laminations to give maximum efficiency, and minimum Eddy current losses. The stators are epoxy coated to prevent shorts, and are wound with wire that is rated at 180 degrees C (356 F). The magnets used in Scorpion Motors are rated for operation at 200 degrees C (392 F), making a motor that is virtually impossible to burn up in normal use.

  Scorpion Motors are built to last, and are backed with a 2-Year warranty against defects in materials or workmanship. However, due to the high RPM of these motors, and the fact that we cannot control the installation and setup, the bearings are not covered by the 2-Year warranty, nor is any subsequent damage caused to the motor by a bearing failure. Bearings are a normal wear item, and as such, need to be maintained and changed periodically. For maximum life, make sure that a sufficient gap is left between the pinion and main gear during motor installation to avoid binding, and put a small drop of oil on each bearing every 5-6 flights. It is the responsibility of the pilot to ensure that the bearings are maintained properly.

  Specifications
  Stator Diameter: 50 mm (1.56 in)
  Stator Thickness: 30 mm (1.024 in)
  No. of Stator Arms: 12
  Magnet Poles: 14
  Motor Wind: 16 Turn Delta
  Motor Wire: 15-Strand 0.33 mm
  Motor Kv: 220KV RPM / Volt
  No-Load Current: (Io/10V) 1.03 Amps
  Motor Resistance (Rm): 0.027 Ohms
  Max Continuous Current: 70 Amps
  Max Continuous Power: 2590 Watts
  Weight: 606 Grams (21.38 oz)
  Outside Diameter: 59.8 mm (2.35 in)
  Shaft Diameter: 7.98 mm (0.314 in)
  Body Length: 60.9 mm (2.39 in)
  Overall Shaft Length: 118.6 mm (3.67 in)
  Max Lipo Cell: 10s
  Shaft Material: Titanium
  Motor Timing: 5deg
  Drive Frequency: 8kHz
  

  
  

  Предложить перевод