ZMR 250 Carbon Fiber Quadcopter DIY Frame Kit with CC3D Flight Controller Brushless Motor ESC Set

К сожалению, у нас нет точной информации, когда ожидаются поставки конкретных товаров. Лучше не добавлять в посылку отсутствующие товары, либо быть готовым ожидать неходовые товары несколько месяцев. Были случаи, что отсутствующие товары исключались из продажи.
Имеет смысл разделить посылки. Одна полностью укомплектованная, другая с отсутствующими товарами.

Чтобы после прихода на склад отсутствующий товар автоматически зарезервировался за Вами, необходимо оформить и оплатить его в заказе.

• Описание товара на английском от 22 января 2016 г.

  Features:
  Carbon Fiber Mini 250 FPV Quadcopter Frame
  Materials: Carbon Fiber Only
  Size: 220mm diagonally, 175mm wide, 130mm long motor-to-motor
  Maximum Propeller: 5 inch
  Motor Mount: M2 12mm - 16mm
  Flight Controller Mount: 30.5mm x 30.5mm
  Board Camera Mount: 32mm x 32mm
  
  32 Bits Processor CC3D Flight Controller
  CC3D Flight Controller Introduction:
  OpenPilot is a next-generation Open Source UAV autopilot. It is a highly capable platform for multi-rotor craft, helicopters, as well as fixed wing aircraft. It has been designed from the ground up by a community of passionate developers from around the globe, with its core design principals being quality, safety, and ease of use? Simplicity does not come with any compromises either: with no hard-coded settings, a complete flight plan scripting language and other powerful features. OpenPilot is an extremely capable UAV autopilot platform
  
  Powerful STM32 32-bit Microcontroller Running at 90MIPs with 128KB Flash and 20KB RAM
  • 3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer.
  • Tiny 36mm x 36mm 4 layer PCB for superior electrical noise reduction and flight performance.
  • Software support for Windows, Mac and Linux.
  • Direct high speed USB support with no drivers required, a truly plug and play device.
  • Spektrum satellite receiver support.
  • Futaba S-BUS hardware support.
  • Innovative flexi-port technology for superior port flexibility.
  • 4Mbits on-board EEPROM for configuration storage.
  
  1806 2280kv Brushless Motor
  KV: 2280
  Max Trust: 460g
  No. of cell: 2-3S
  Framework: 12N14P
  Propeller: 5 inch - 6 inch
  Length: 26.7mm
  Shaft: 2mm
  Diameter: 23mm
  Weight: 18g
  
  12A Simonk ESC
  Max continuous load: 11 amps
  Burst Current: 16A / 10sec
  BEC: 5v/1amp max
  Lipo Cells: 2 to 3 cells
  Cables are fitted with female 2mm bullet connectors
  Weight: 10g
  Dimensions: 24mm L x 18mm W x 7mm H ( 29mm in length including capacitor )
  15cm signal wire / 5v power
  5cm motor wires ( including 2mm bullet connector )

  Specification

  General	Type: Frame Kit
  Dimension and Weight	Package weight: 0.6150 kg Product size (L x W x H): 22.00 x 17.50 x 13.00 cm / 8.66 x 6.89 x 5.12 inches Package size (L x W x H): 32.00 x 20.00 x 8.00 cm / 12.6 x 7.87 x 3.15 inches
  Package Contents	Package Contents: 1 x 250 Quadcopter Frame, 4 x Propeller, 4 x Brushless Motor, 4 x 12A ESC, 1 x CC3D Flight Controller, 1 x Connecting Cable Set, 1 x Accessory Set

  Product Safety Disclaimer:
  We do not accept any responsibility or liability for misuse of this or any other product. All our products are extensively tested to comply with rigorous and strict QC standards. For certain products (e.g. toys, knives, etc.), we recommend proper supervision as we cannot be held liable for misuse or accidents.

  
  

  Предложить перевод