FRF3_EVO_BRUSHED Flight Controller Built-in Frsky 8CH Sbus Receiver For Eachine QX95 QX90 QX90C

К сожалению, у нас нет точной информации, когда ожидаются поставки конкретных товаров. Лучше не добавлять в посылку отсутствующие товары, либо быть готовым ожидать неходовые товары несколько месяцев. Были случаи, что отсутствующие товары исключались из продажи.
Имеет смысл разделить посылки. Одна полностью укомплектованная, другая с отсутствующими товарами.

Чтобы после прихода на склад отсутствующий товар автоматически зарезервировался за Вами, необходимо оформить и оплатить его в заказе.

• Описание товара на английском от 19 ноября 2016 г.

  FRF3_EVO_BRUSHED Flight Controller Built-in Frsky 8CH Sbus Receiver For Eachine QX95 QX90 QX90C
  
  Description:
  Brand Name: Eachine
  Item Name: FRF3_EVO_BRUSHED Flight Controller Built-in Frsky Receiver
  Item NO.: QX958FR
  Dimension: 22mm*32.5mm
  Thickness: 1.2mm
  Weight: 3g
  Receiver: Frsky 8CH sbus receiver(D8 mode)
  Coreless motor plug: SH1.0
  Firmware: SP RACING F3 EVO 1.13.0
  Support work voltage: 3.6v~4.2v(1S Lipo battery)
  
  Features:
  1.F3_EVO_Brush revision is out of the F3 EVO SP RACING is based on a SP RACING F3 EVO firmware 32 brush flight control.
  2.Independent design of the circuit structure
  3.Using STM32F303CCT6 + MPU6500, advanced hardware platform F3 guarantee more stable flight.
  4.With a large and high quality current NMOS transistors, operating current of up to 10A or more. Each Brushed motor is equipped with freewheeling diodes.
  5.Integrated 2.4G Frsky 8CH sbus receiver(D8 mode).
  6.With battery voltage detection and buzzer interface(solder pad)
  7.LED_STRIP Function(solder pad)
  
  Connection diagram:
  
  
  
  Receiver configuration:
  
  Enable Seria_RX for UART2 and Set Receiver mode RX_SERIAL ,Select SBUS in Cleanflight or Betaflight configurator.
  
  
  
  Bind procedure:
  1.Turn on the transmitter , select D8 mode for the Receiver.
  2.Connect the battery to the board while Jumped the two “BIND” pins on the Board, the green LED will get be solid, this indicates the receiver get into the binding mode.
  3.Move to the Receiver [Bind] option in the transmitter and ENT to Bind with the receiver, The transmitter beeps.
  The green LED on the board will turning off, this indicates that the bind process was successful. Reconnect the battery for the flight controller, and the green LED on the receiver is solid again. It means connection is established with your transmitter
  
  Note:
  If you flashed the firmware or erase chip, please first do the bellowing procedure , don’t connect the battery otherwise the motor will auto-spin
  1.Cleanflight: Go to the CLI tab, type “Set motor_pwm_rate=1000” ,then enter save
  2.Betaflight: Go to Configure Tab and set ESC/Motor protocol to BRUSHED
  *This step is in order to avoid motor auto-spinning when connect the battery
  
  Package included:
  1 x FRF3_EVO_BRUSHED Flight Controller

  
  

  Предложить перевод