Matek Systems HUBOSD8-SE w/STOSD8-SE, Current Sensor, Dual BEC and 6S Max

К сожалению, у нас нет точной информации, когда ожидаются поставки конкретных товаров. Лучше не добавлять в посылку отсутствующие товары, либо быть готовым ожидать неходовые товары несколько месяцев. Были случаи, что отсутствующие товары исключались из продажи.
Имеет смысл разделить посылки. Одна полностью укомплектованная, другая с отсутствующими товарами.

Чтобы после прихода на склад отсутствующий товар автоматически зарезервировался за Вами, необходимо оформить и оплатить его в заказе.

• Описание товара на английском от 21 июля 2017 г.

  Matek Systems have once again come out with an excellent multifunction Power Distribution Board (PDB) for use with mini FPV drones that run 3 to 6S Lipo batteries.

   

  The HUBOSD8-SE comes with great features that will meet all your needs. The new, built-in, STOSD8-SE (OSD) can support Plug and Play, so no complicated settings are needed. 30A of power can be provided to each ESC (total of four ESCs). There are Dual BECs to provide both 5V at 1.5A and 10V at 1.5A will meet all peripheral power requirements. Note that the 10V output can be used to power 12V cameras. The built-in current sensor measures up to 184A.

   

  This is a powerful PDB that will meet all your mini-drone requirements.

   

  Features:
  • Built-in STOSD8-SE can support Plug and Play
  • Current Sensor 184A max
  • 2oz copper, 4-layers & 2mm PCB
  • 1x Battery input, 4x ESC outputs. 2x BEC 5V outputs, 2x BEC 10V outputs
  • Camera signal and ground pads, Video Transmitter Signal and ground pads
  • 1x Serial port (RX, TX, G)
  • RSSI input pad and Current sensor output pad

   

  Specs:
  General:
  Input voltage range: 9 - 27VDC (3~6s LiPo) w/ TVS protection
  PDB: 4x30A (Max.4x46A)
  Regulated 5V (POSCAP filtered) and 10V (MLCC filtered) outputs
  Physical:
  Dimensions: 46x36x4mm
  Weight: 9g
  Mounting holes: 30.5mm square spacing, diameter 3mm
  PDB (ESC outputs):
  Continuous current: 30A per output
  Peak current (5 seconds/minute): 46A per output
  BEC 5V outputs:
  Designed for RC Receivers, Flight controllers, OSD, and Servos.
  Voltage: 5.0 +/- 0.1VDC
  Continuous current: 1.5 Amps (Max.2A 10s/minute)
  Output Ripple: 23mV (VIn=24V, VOut=5V@1.5A load)
  Short-circuit tolerant: 2 seconds/minute
  BEC 10V outputs:
  Designed for Video TX or FPV camera.
  Voltage: 10.0 +/- 0.2VDC
  Continuous current: 1.5 Amps (Max.2A 10s/minute)
  Output Ripple: 15mV (VIn=24V, VOut=10V@1.5A load)
  Short-circuit tolerant: 2 seconds/minute
  10V can be used to power cameras labeled as 12V
  The 3S LiPo input voltage should be 10.8V plus
  Current Sensor:
  Current: 184A Max
  Current signal output: 3.3V ADC for Flight Controller

  
  

  Предложить перевод