Радиоуправляемые модели самолетов, вертолетов, автомобилей, катеров, яхт и танков.
Гарантируем ваше удовольствие либо возврат денег. На сайте огромное количество отзывов о нашей работе и товарах.
Модуль питания HKPilot Mega 10s с разъемами XT60
-
The HKPilot HV Power Module incorporates both a way to power your HKPilot and accessories as well as report battery voltage and current back to the HKPilot for logging and telemetry data. This can be viewed in the HKPilot’s stored logs or live with a telemetry radio connection. All thru a single and tightly included 6-pin cable that directly matches the HKPilot’s/APM/PX4 connector. The on-board switching regulator outputs 5.3V at a maximum of 2.25A, and can be used up to 45Volts (10S LiPo) and at a maximum of 90 amps. The Power Module is ready to use with XT60 connectors pre-fitted, and shrink wrapped for protection.
Note: The Power Module is rated at 2.25 Amps to power the HKPilot, receiver and peripherals (GPS and Telemetry radio) ONLY. To power servos use an ESC with an adequate BEC or a standalone BEC plugged into the output bus, and remove jumper 1 to isolate the two power lines.
Specifications:
Max input voltage: 45V
Max current sensing:90A
Switching regulator outputs: 5.3V at 2.25A max
Connector: 6-pos Molex cable plugs directly to HKPilot/APM/PX4 'PM' connector
Voltage and current measurement configured for: 5V ADC
Includes:
DF13 6 Position Connector 150mm long
HKPilot Power Module with XT60 Connectors*Note: The reference to APM refers to the ArduPilot project, a family of open source autopilots based on the Arduino open source computing platform, developed by 3DR and the open source community. It consists of a choice of ArduPilot Mega (APM) electronics and a range of free software versions for different vehicles and is governed by an open source creative commons license.
*Note: This is not an original Arduino brand product.
-
Перевод устарел, чуть выше - новое англоязычное описание товара!
Модуль питания HKPilot HV позволяет не только питать полетный контроллер HKPilot и аксессуары, но и измерять параметры подключенной батареи. Данные о напряжении и токе могут записываться в память полетного контроллера для последующего анализа или выдаваться в реальном масштабе времени через телеметрийный канал связи. Все данные поступают через один 6-контактный кабель, который подключается непосредственно к разъему полетного контроллера APM/PX4 HKPilot. Встроенный импульсный преобразователь напряжения выдает 5.3В при максимальном токе 2.25A. Модуль расчитан на измерение напряжения до 45В (10S LiPo) и тока до 90А. Силовой модуль поставляется готовым к работе с напаянными разъемами XT60. Места пайки разъемов защищены термоусадкой.
Примечание: модуль питания может выдать не более 2,25А для питания ТОЛЬКО полетного контроллера HKPilot, приемника и периферийных устройств (GPS и радиотелеметрия). Для питания сервоприводов используйте регулятор с адекватным BEC или автономно BEC, подключенный к выходной шине, и удалите перемычку 1 чтобы изолировать две линии питания.
Технические характеристики:
Максимальное измеряемое напряжение: 45В
Максимальный измеряемый ток: 90A
Импульсный стабилизатор напряжения: 5.3В, 2.25A max
Разъем: 6-контактный Molex кабель подключается непосредственно к разъему HKPilot/APM/PX4
Измерение напряжения и тока сконфигурировано для: 5V ADC
Что в посылке:
6-контактный разъем DF13 с кабелем длиной 150 мм
Модульпитания HKPilot с XT60 разъемами
* Примечание: ссылка на АРМ относится к проекту ArduPilot, семейству автопилотов с открытым исходным кодом на основе вычислительной платформы Arduino, разработанной 3dr. Эти автопилоты состоят из основного контроллера ArduPilot Mega (APM) и ряда бесплатных версий программного обеспечения для различных транспортных средств.
-
The HKPilot HV Power Module incorporates both a way to power your HKPilot and accessories as well as report battery voltage and current back to the HKPilot for logging and telemetry data. This can be viewed in the HKPilot’s stored logs or live with a telemetry radio connection. All thru a single and tightly included 6-pin cable that directly matches the HKPilot’s/APM/PX4 connector. The on-board switching regulator outputs 5.3V at a maximum of 2.25A, and can be used up to 45Volts (10S LiPo) and at a maximum of 90 amps. The Power Module is ready to use with XT60 connectors pre-fitted, and shrink wrapped for protection.
Note: The Power Module is rated at 2.25 Amps to power the HKPilot, receiver and peripherals (GPS and Telemetry radio) ONLY. To power servos use an ESC with an adequate BEC or a standalone BEC plugged into the output bus, and remove jumper 1 to isolate the two power lines.
Specifications:
Max input voltage: 45V
Max current sensing:90A
Switching regulator outputs: 5.3V at 2.25A max
Connector: 6-pos Molex cable plugs directly to HKPilot/APM/PX4 'PM' connector
Voltage and current measurement configured for: 5V ADC
Includes:
DF13 6 Position Connector 150mm long
HKPilot Power Module with XT60 Connectors*Note: The reference to APM refers to the ArduPilot project, a family of open source autopilots based on the Arduino open source computing platform, developed by 3DR and the open source community. It consists of a choice of ArduPilot Mega (APM) electronics and a range of free software versions for different vehicles and is governed by an open source creative commons license.
Упоминается в статьях и вопросах
Чтобы общаться и совершать покупки необходимо зарегистрироваться.
Это просто и займёт всего одну минуту.
Спасибо за регистрацию!
Для подробностей, наведите курсор на одну из картинок.
Удаленные товары | |||||||
Очистить |
Максимальное измеряемое напряжение: 45В
Следовательно 12S максимум.